Asphalt Overlay Interlayers: Choosing Between Mat, Grid and Composite Systems


Asphalt Overlay Interlayers: Choosing Between Mat, Grid and Composite Systems

Specifiers choose intumescent coatings for what happens at high temperature: at roughly 200-300°C, the additives in the film .decompose and the coating swells into a thick, porous, insulating char that slows heat reaching the protected steel. That char is the product. It is also, mechanically, the weakest thing in the system — a baked foam clinging to a surface, expanding under fire while gravity and gas flow pull at it. This is why serious passive fire protection systems embed a reinforcing mesh inside the coating: a hidden skeleton that keeps the char in place and structurally continuous when the fire tests it.

This article explains how unreinforced char fails, what the skeleton actually does and where it sits inside the coating, how to choose between glass, carbon, metal and basalt meshes, and where a fiberglass laid scrim fits in coating manufacturers’ systems.

How unreinforced char fails

Fire-exposed intumescent films show a consistent set of failure modes — described across the patent and research literature rather than in coating marketing, which is one reason the skeleton gets so little airtime:

Table 1 — Failure modes of unreinforced intumescent char, and what counters them

Failure mode What happens Where it bites hardest What the mesh does
Char splitting Cracks open in the swelling char and propagate inward; insulation short-circuits at the crack Wide flange tips, corners, rectangular sections Mesh at depth halts downward crack propagation and preserves insulation below
Char sagging / flow Soft char deforms under gravity and erosion on long or intense fires Vertical and sloped surfaces, jet-fire exposure contexts Tensile continuity holds the char body together
Delamination The whole char layer detaches from the substrate, exposing bare steel Poor bond zones, mismatched layer chemistries Mesh anchors the char body to the coating system
Edge and corner loss Expansion and stress concentrate at geometry changes Corners of beams, bolt heads, edges Continuous mesh bridges stress concentrations

The underlying physics is simple: the char must expand — sometimes several times its applied thickness — to do its insulating job, but a swollen foam has little tensile strength. Any crack that reaches the substrate short-circuits the thermal protection locally, and steel temperature at that spot rises far faster than the fire rating assumes. A reinforcing mesh does not stop the chemistry; it gives the expanding char a skeleton to grow through and hold on to — exactly the role our own coating-range materials play in the field: the mesh holds the char together so the protective barrier stays intact.

Cross-section of an intumescent coating with an embedded scrim: the mesh at mid-depth stops a char crack from propagating down to the steel

Mesh embedded in the intumescent coating halts char splitting

Where the skeleton sits: mesh depth and placement

Patent literature on intumescent mesh systems converges on a specific placement rule: the mesh belongs at roughly one-third to two-thirds of the total coating thickness. The logic cuts both ways:

  • Too shallow, and the mesh sits in the zone of greatest expansion — it can restrain the upper char and interfere with the free swelling that produces insulation.
  • Too deep, and the mesh is closer to the heat source and the substrate, doing less to stop surface-initiated splits and adding little structural value.

Placement is also a process discipline. The typical application embeds the mesh into a lower coat that has gelled enough to hold it but is still open enough to accept it: the mesh is pressed into the lower layer — often rolled in with a solvent-wetted roller — and the next coat is applied over it. Keeping one chemistry system avoids delamination and slip planes between layers.

For coating producers, the practical consequences are specific:

  • The mesh must be thin and light enough not to consume the coating’s thickness budget (6-16 g/m² typical).
  • It must wet out and bond with the coating chemistry.
  • It must be dimensionally stable through application and curing.

Choosing the mesh material

Table 2 — Mesh materials for coating reinforcement: engineering trade-offs

Material Temperature behavior Chemistry & handling Practical position
Glass fiber scrim Incombustible fiber; stable through char-formation temperatures Alkali-resistant; bonds well; light and thin The workhorse: cost-effective, stable, easy to embed
Metal wire mesh Strong but conducts heat; heavy; corrosion risk Stiff; harder to cut/form Where mechanical abuse dominates
Carbon fiber mesh High temperature capability; conductive Premium cost; specialist handling High-spec systems; EMI/antistatic roles
Basalt / mineral fiber mesh Refractory by nature Less common supply chains Niche refractory systems

GADTEX fiberglass laid scrim range

GADTEX (RUIFIBER GROUP) supplies fiberglass laid scrim — a chemically bonded, open-mesh continuous-filament fabric — used by coating and fire-protection product manufacturers as reinforcement.

Fiberglass laid scrim roll for coating reinforcement

Open-mesh fiberglass laid scrim

Table 3 — GADTEX fiberglass laid scrim data sheet

Item Mesh size Weight
CF12.5*12.5PH 12.5 × 12.5 mm 6.2-6.6 g/m²
CF10*10PH 10 × 10 mm 8-9 g/m²
CF6.25*6.25PH 6.25 × 6.25 mm 12-13.2 g/m²
CF5*5PH 5 × 5 mm 15.2 g/m²
Fiberglass scrim detail

Scrim structure detail
Fiberglass scrim application range

Laid scrim in coating and composite applications

Mesh openness is a selection lever, not a cosmetic one: a 12.5×12.5 mm open mesh at ~6.5 g/m² lets a thick coating pass through and bond in one placement, while a 5×5 mm mesh at ~15.5 g/m² gives denser reinforcement for thinner films.

RFQ checklist and FAQ

What to send for a scrim recommendation:

  1. Coating system and chemistry (epoxy, acrylic, others), applied thickness per coat and total
  2. Substrate type and geometry (beams, columns, vessels, tanks — flat vs curved)
  3. Application process (trowel, spray, roller; mesh embedment step)
  4. Exposure environment (humidity, chemicals, coastal)
  5. The fire scenario and regulatory context your system is being tested against

How deep should the mesh sit in the coating?

Patent literature on intumescent mesh systems places it at one-third to two-thirds of the total coating thickness — shallow enough to stop surface-initiated splits, deep enough not to restrain free expansion.

Won’t the mesh restrict char expansion?

Correct placement avoids this. At mid-depth the upper char is free to expand above the mesh while the mesh keeps the lower char and the coating-to-substrate bond intact.

Fiberglass or carbon fiber mesh — how do I choose?

For most coating systems, fiberglass scrim is the pragmatic choice. Carbon fiber enters where specifications demand it (including dual EMI/antistatic roles) at a premium.

A correctly placed fiberglass skeleton is how coating manufacturers make structural safety the default outcome.

Send your coating system, substrate and application process for a scrim recommendation:

Contact Us for Recommendation

WhatsApp Online Chat !