FRP pipe surface mat veil release film filament winding surface treatment materials


The Surface System in Filament-Wound FRP Pipe: Release Film, Surface Veil and Laid Scrim

On a continuous filament winding line, a pipe’s inner surface is settled in the first few metres of mandrel travel — before a single structural roving is laid down. Three materials decide it: the release film wrapped onto the steel band, the surface veil that becomes the resin-rich liner, and the laid scrim that holds the wet build together. The sequence never changes. What changes from plant to plant is whether those three were specified as one system or bought separately from three catalogue pages.

This guide follows the mandrel position by position, and for each material asks which spec line decides whether it runs on the line — and where a mistake shows up.

The mandrel is a sequence, not a purchase order

Continuous winding process descriptions agree on the order. A release film is applied to the steel band first, protecting the mould surface and easing extraction. A chemical-resistant C-glass layer follows and becomes the resin-rich inner liner. Then an anti-diffusion barrier of resin and chopped glass, then the structural winding, and finally an outer surfacing veil.

Compare that with how the same materials are sold. Our FRP materials range is organised by family: release films under surface treatment and protection, veils and scrims and chopped strand under surface treatment and reinforcement, tapes and nettings under adhesive and fastening. That is a purchasing structure — it groups things by how they are made and shipped, not by where they sit on the mandrel.

Material Position on the mandrel Job it does What goes wrong First spec line to fix
Release film 1 — directly on the steel band Protects the mould, sets the inner wall finish, allows extraction Wrinkles print into the liner; a tear or a bond means rework from inside a cured pipe Continuous service temperature, then width and roll length
Surface veil 2 — fluid face of the liner Carries a resin-rich layer that blocks wicking into structural glass Dry spots, wrinkles and tears become leak paths Grammage and wet-out, then tensile at line tension
Laid scrim 3 — wrap layer within the build Holds the wet build together, distributes resin, stabilises the lay-up Layer shift, resin pooling, poor wet-out at speed Mesh and binder add-on, then roll format

 

Release film: the first material on, the last thing specified

The film is applied at the very start of the line and leaves the plant at the very end — peeled out of the finished pipe from the inside, after cure. In between it keeps resin off the steel band, defines the surface the fluid will touch, and makes extraction possible at all.

Yet the film is usually the cheapest line in the bill of materials and the most expensive one to get wrong, because failure is not caught at incoming inspection but as a wrinkle printed into the liner, a film that will not release, or a tear repaired from inside a cured pipe. Purchasing files it as a consumable; the line treats it as process-critical, and the specification has to satisfy the second view.

The spec lines that carry the risk are unglamorous: thickness, width, roll length, tensile and elongation at line tension, and release level. The first two set how the film follows the band without wrinkling; roll length sets how often the line stops; release level decides whether the next shift is spent extracting film or making pipe.

GRP film or GRE film: a resin question wearing a temperature label

Catalogues usually split release film two ways. Ours describes a GRP film as more heat-resistant, suited to high-temperature moulding and better matched to unsaturated polyester, and a GRE film as intended for room-temperature moulding, with a high polish and better compatibility with epoxy. The deciding variable is the resin system; temperature is the consequence. A polyester line runs hot for its cure schedule and exotherm; an epoxy line often runs near ambient and cares more about polish and release.

da1968fc03cf9438cc7e1d012dd1311c
0eda34abb63901d9fef601e9341944b
p983925001396604863_副本

That distinction matters because “high temperature” is not a specification. Our BOPP film page calls the product high-temperature resistant and suitable for GRP and GRE pipe work, yet states no continuous service temperature. Equipment builders simply name the film they design around — one continuous winding line description specifies a mylar release film on the mandrel, mylar being PET. In the consumables market, films are quoted by polymer family against a temperature band, because a band is something a process engineer can check against a cure cycle.

Two rules follow. Ask for continuous service temperature and the peak the film will see during cure and exotherm, in writing, and compare both with your cycle rather than with a competitor’s adjective. And do not port temperature tables from vacuum-bagging films: the mechanical duty is not the same.

Surface veil: the carrier of the corrosion barrier

The veil is the most misunderstood of the three, because it looks weak and is often described as reinforcement. Its job is not strength. In a corrosion barrier the veil holds a resin-rich layer at the fluid face, and that layer is what keeps the medium from reaching structural glass, where wicking along fibre bundles would undermine the laminate. Corrosion-control construction puts the veil at the inner face, backed by chopped strand mat, with the structural laminate behind.

Because the veil’s function is to be saturated, its processing behaviour is a specification issue. On a continuous line the veil is pulled under longitudinal tension; a veil that tears or wrinkles at speed produces uneven liner thickness, and uneven thickness produces exactly the stress concentrations the barrier was meant to avoid. Slow wet-out leaves micro-voids that surface months later as blistering — a mechanism veil suppliers describe in their own literature, and worth treating as a supplier claim rather than an independent finding.

For a market reference, one veil mill publishes a family at 30, 50 and 90 g/m², at 11, 19 and 31 mil, with binder limits tightening as the veil gets heavier. The trade-off is visible there: heavier veil holds more resin and covers better, but wets out more slowly and conforms less readily on a curved mandrel. Glass type is a separate decision, with C-glass chosen for chemical resistance at the fluid face.

One honest note: surface tissue and polyester veil are part of the FRP materials we supply, but we publish no datasheet for them, so grammage, binder and roll format are confirmed in writing at quotation. Apply the same rule to any supplier.

What the published barrier numbers say, and why they disagree

Ask three sources what a corrosion barrier should contain and you get three answers — what happens when a product-line internal control is quoted as an industry norm.

Source Resin content Barrier construction What the number actually is
Pipe maker A specification guide 80% nominal in veil layers; 60% minimum in mat layers 10 mil synthetic veil + 10 mil glass veil + plies of 1.5 oz chopped strand mat to the specified liner thickness Internal specification for that maker’s 14″–72″ product line
Pipe maker B technical dossier At least 70% C-glass surface mat reinforced liner, at least 0.5 mm thick Internal control for that maker’s standard range
Industry media, quoting a resin supplier About 90% in the veil; about 70% in the mat Barrier typically 100–125 mil, veil first, then at least two plies of 1.5–2.0 oz/ft² mat Formulation convention described for corrosion-control work generally

The spread is real, and not only rounding: the two makers differ by an order of magnitude on liner thickness, since 0.5 mm is roughly 20 mil while the quoted 100–125 mil is 2.5 to 3.2 mm. Liner thickness tracks pressure class, diameter, medium and design life, so a maker publishing one value is describing a product family, not the physics of barriers.

So the useful question is not “what is the industry value” but “what is the basis of this number”. Three checks settle most of it: internal control or general practice; veil layer alone or whole barrier; units in mil, mm or percent by weight. A specification copied across without those answers will be wrong in a way that only shows up in service.

Standards do not resolve it either, and are not meant to. ASTM D2996 covers machine-made filament-wound reinforced thermosetting resin pressure pipe, classifies it by type, grade and class, and adds a cell classification for mechanical properties; it sets out what a maker must declare and test, not a recipe for a liner. A standard clause quoted as a fixed resin percentage is usually being misread — hence paraphrase here, not quotation.

Laid scrim is a wrap layer, not a barrier layer

Our own application notes are explicit that a laid scrim enters a pipe structure as an intermediate reinforcement or wrap layer, not as the structural winding and not as the corrosion barrier. If the term is new to you, what a laid scrim actually is covers the construction; three roles are what matter here:

1.Structural layer — continuous roving in hoop and helical paths, carrying pressure and external loads.
2.Barrier layer — veil plus chopped strand mat at the fluid face, resin-rich by design.
3.Wrap layer — an open-grid scrim that holds the wet build together, stabilises the lay-up, distributes resin and adds handling robustness.

For that role, the grid matters more than the grammage headline. Our GRP piping grade comes in four constructions — 2.5 × 5 mm at 5.5–6 g/m², 2.5 × 10 mm at 4–5 g/m², 4 × 6 mm at 7.8–10 g/m² and 8 × 12.5 mm at 2–2.5 g/m² — with 0.8–3 yarns/cm mesh, 200–2,500 mm widths, rolls to 50,000 m and PVOH, PVC or acrylic binders. The open mesh is the functional feature: resin passes through, so the scrim stabilises the lay-up without sealing the surface the way a mat would.

This is where a roofing carrier and a pipe wrap part company. A membrane carrier is specified for the dimensional stability of a finished sheet on a calender line; a pipe wrap is specified for how it behaves while wet, under tension, on a moving mandrel. Our GRP pipe application notes leave the hoop and axial design with the structural laminate, which is where it belongs — a scrim will not raise a pipe’s pressure rating, and nothing in the published record suggests otherwise.

The spec lines that decide whether the system runs

Spec line What it controls How it shows up when it is wrong
Veil: grammage and wet-out rate Whether the veil saturates before the line moves on Dry patches and micro-voids; blistering months later
Veil: tensile at line tension Whether the veil survives being pulled onto the mandrel Tears and wrinkles; uneven liner thickness
Scrim: mesh and binder add-on Resin distribution and layer stability during winding Layer shift, resin pooling, poor wet-out at speed
Film: width, roll length, elongation How the film follows the band and how often the line stops Wrinkles printed into the liner; excessive changeovers; release problems

None of these appears on a data sheet as a single number. A veil with the right grammage and the wrong tensile passes incoming inspection and still fails at speed; a scrim with the right mesh and the wrong binder add-on pools resin in the wrong place. The specification therefore has to be written against the line — speed, tension, cure schedule, mandrel diameter — not only against a material standard. Our specification-level selection guide covers how those rows read on a scrim sheet.

What to send before asking for a recommendation

Six items change the answer; send all six:

1.Pipe diameter and pressure class, which set liner thickness and the structural build.
2.Resin system and cure schedule — polyester or epoxy, ambient or elevated, with the peak the film will see.
3.Forming route — continuous winding, static mandrel winding or centrifugal casting; each loads the surface materials differently.
4.Target liner construction — thickness and resin content, and whether the target comes from a standard or your own qualification.
5.Film format — width, roll length, and how film is removed after cure.
6.Veil preference — glass type, grammage band, and whether a longitudinal-reinforced veil is needed at your line tension.

FAQ

Can I use a vacuum-bagging release film on the mandrel?

They are different product classes. Bagging films are sacrificial membranes under vacuum, quoted against a cure band; a mandrel film is a tensioned wrap on a moving steel band that must also survive extraction from inside a cured pipe. Ask for continuous service temperature, elongation and release level against your line, not a bagging datasheet.

Is a heavier surface veil always a better corrosion barrier?

No. Heavier veil holds more resin and covers better, but wets out more slowly and conforms less readily to a curved mandrel — and on a fast line, slow wet-out leaves the voids that become blisters.

Can a laid scrim replace chopped strand mat in the barrier?

No. The mat bulks the resin-rich layer and covers the fluid face in multiple directions; the scrim is an open grid meant to stabilise the lay-up and let resin through. Substituting one for the other changes what the barrier is, not just how thick it is.

Can the same surface materials run both GRP and GRE?

Treat the film as a separate decision. Polyester and epoxy differ in cure temperature and release behaviour, which is exactly the axis on which catalogues split GRP and GRE films. Veil and scrim may carry over, but their binder compatibility and wet-out need confirming against the specific resin, in writing, before the trial.

Send us your pipe construction

Three materials, bought from three different pages, decide a filament-wound pipe’s inner surface — and almost nobody specifies them as a set. If you are setting up a liner, or chasing blisters, wrinkles or release problems that keep coming back, send your pipe diameter, pressure class, resin system, cure schedule and forming route through our contact page. Our engineers will map them onto a surface system — film, veil and wrap scrim — and put the specification in writing.

Address

Head office Add: BLDG#26,MAX Technology Park Phase II,Baoshan District,Shanghai China
Factory Add: Shanghai Ruifiber (Fengxian) Industry Park, Fengxian, Xuzhou, China

E-mail

Lgl_1100@vip.163.com

Ruifibersales2@ruifiber.com

Phone

0086-21-56659615(Sales dept)

0086-18621915640

0086-1561815 6160

Hours

24-hour Service

WANT TO WORK WITH US?


CONTACT US

WhatsApp Online Chat !