The Hidden Skeleton in Fire Protection Coatings: How Scrim Holds the Intumescent Char


The Hidden Skeleton in Fire Protection Coatings: How Scrim Holds the Intumescent Char

A fresh overlay is the most visible promise in road maintenance: mill the old surface, lay new hot mix, and the road looks new again. The problem is that the old pavement underneath does not forget its cracks. Within a season or a few years, the joints and cracks below reappear in the new layer — a failure mode the industry calls reflective cracking. Interlayers exist to interrupt exactly this process. Choosing one, however, is not a search for a single “best” product. Mats, grids and composites work by different mechanisms, and the right choice depends on the condition of the existing pavement, the traffic it carries and how much waterproofing the section needs. This article sets out those boundaries, then shows where a fiberglass nonwoven overlay system fits.

Why new overlays crack: the reflective cracking problem

An asphalt overlay sits on a substrate that is already cracked or jointed. Three loading mechanisms conspire to grow those defects upward:

  • [!] Traffic bending: A wheel load passing over a crack opens and closes it like a hinge. The crack tip concentrates tensile strain in the overlay directly above.
  • [!] Thermal cycling: Daily and seasonal temperature swings make the old slab expand and contract. Horizontal movement at the crack drags the overlay back and forth in shear, which is often more damaging than the vertical bending itself.
  • [!] Water: Once a reflective crack reaches the surface, it becomes an entry point for water. Pumping, stripping and potholes follow, and the overlay ages far faster than its design life assumed.

Stress concentrations at a crack tip are localized and severe. That is precisely why a thin layer with the right mechanical behavior — placed between the old surface and the new hot mix — can change the failure mode of the whole section. Reinforcement suppliers describe the role as a stress-absorbing or strain-distributing interlayer: it either absorbs the horizontal movement at the crack, or adds enough tensile stiffness to spread the concentrated strain over a wider area — see also our note on stress-absorbing interlayers for roads.

The three interlayer families

Interlayers for overlays fall into three structural families. The figure below shows how each sits between the old pavement and the new overlay.

Table 1 — Mat vs grid vs composite at a glance

Family Typical structure Primary mechanism Best fit Watch-outs
Mat (nonwoven / membrane) Fiberglass or polyester nonwoven mat, often pre-coated with polymer-modified asphalt (e.g. SBS) Stress absorption + moisture barrier; bridges the crack and seals it Sections with active cracking plus a waterproofing need; bridge decks; maintenance overlays Adds a deformable layer — binder and compaction control matter; not a structural stiffener on its own
Grid (geogrid) Fiberglass or polyester open mesh, coated for bitumen compatibility Tensile stiffness at very low elongation; locks aggregate and spreads crack-tip strain Structurally driven reinforcement on a sound, well-bound substrate; rutting and fatigue control Does not seal; needs full bond through the mesh openings; sensitive to installation damage
Composite (grid + nonwoven) Geogrid laminated to a nonwoven fabric Reinforcement plus membrane in one product Heavy traffic where both crack control and waterproofing are required Higher cost; placement still depends on bonding and compaction quality

The important reading of Table 1 is directional, not hierarchical. A mat does not “under-perform” a grid — it does a different job. Where the dominant problem is an old, cracked, possibly damp surface that needs sealing as much as strengthening, the membrane behavior of a mat is the point.

Selection boundaries by site condition

Table 2 — Choosing by what the site tells you

Site condition Dominant concern Lean toward Why
Cracked surface, water visible or suspected Sealing + crack bridging Mat (or composite) Membrane seals the old surface; a coated mat can bridge existing cracks — up to 5 mm (GADTEX data)
Sound surface, heavy and slow traffic Structural reinforcement, rutting Grid or composite Low-elongation mesh adds tensile stiffness where bending strain concentrates
Bridge deck / structures Waterproofing steel and deck Mat with waterproofing role Impermeable interlayer protects reinforcement from chloride ingress
Freeze-thaw climate Thermal cycling at cracks Mat or composite Service range to match; GADTEX lists -30°C to 80°C

Installation factors that decide performance

Interlayer performance is decided as much by placement as by product choice:

01. Surface preparation Loose material, potholes and step offsets must be repaired first.
02. Tack coat and bond A starved tack coat turns a reinforcement into a slip plane.
03. Compaction temperature Optimal bonding requires hot-mix compaction at 150-160°C.
04. Layout and joints Keep laps bonded and avoid exposed edges at lanes and gutters.

GADTEX fiberglass nonwoven asphalt overlay

GADTEX (RUIFIBER GROUP) produces a fiberglass nonwoven asphalt overlay that combines a nonwoven fiberglass mat with an SBS-modified asphalt coating.

GADTEX fiberglass nonwoven asphalt overlay product
Fiberglass nonwoven mat with SBS-modified asphalt coating

Table 3 — GADTEX Technical Specifications

Material Fiberglass nonwoven + SBS-modified asphalt
Thickness 2.5-4.0 mm (±0.2 mm)
Tensile strength ≥35 kN/m (ASTM D4595)
Service temperature -30°C to 80°C
Asphalt composite interlayer for crack prevention
Interlayer placement over a cracked pavement surface
Asphalt overlay reinforcement diagram
Overlay system over the existing pavement

RFQ Checklist

Send these details for a professional recommendation:

  • Road type and traffic level
  • Crack survey (width, density, activity)
  • Overlay design (thickness, mix type)
  • Climate and temperature range
  • Waterproofing requirements
Contact Us for Recommendation
WhatsApp Online Chat !