Where the Scrim Goes in Resilient Flooring: Rigid Cores (WPC/SPC), LVT Layers, and Paper-Composite Underlayment


Where the Scrim Goes in Resilient Flooring: Rigid Cores (WPC/SPC), LVT Layers, and Paper-Composite Underlayment

Ask a flooring converter what scrim they use and you will usually get a mesh size and a grammage. Ask where it goes, and the answers start to diverge — because the same question has four different answers depending on the construction: flexible LVT, an SPC composite with LVT layers, a plain rigid SPC core, or a paper-composite underlayment under the plank.

ⓘ

That divergence is the practical problem this article addresses. The glass reinforcement layer in resilient flooring is not a universal ingredient added for good measure; it is a structural decision whose value, position, and even necessity change with the core. Get the position right and the layer earns its cost. Get it wrong — or assume every product needs one — and you either pay for reinforcement the structure does not use, or leave a dimensionally unstable stack without the one layer that could have stabilized it.

Four Constructions, One Position Map

Start with the map. Four builds cover most of what ships today, and the scrim sits in a different place in each.

Diagram of four resilient flooring constructions showing where the fiberglass scrim sits — flexible LVT mid-plane, SPC composite below the core with an optional second position, plain SPC core without a glass layer, and paper-composite underlayment

Where the scrim goes: four constructions, four answers

The rest of this article explains why each position makes sense — and where the honest uncertainties are.

Flexible LVT: The Mid-Plane Rule

In a flexible LVT plank, the glass layer belongs near the geometric mid-plane of the product. That is not a convention; it is where the layer restrains bending and thermal movement most efficiently, with the decor film above it protected from the dimensional work happening below.

Placement alone is not enough. In calendered sheet vinyl, the glass mat is impregnated with PVC paste and laminated under heat and pressure so the vinyl fuses around it — the reinforcement is encapsulated, not merely sandwiched. Encapsulation is what prevents delamination and keeps the reinforcement effective for the life of the floor.

Woven glass mat and laid scrim both appear in this position, and the choice between them is a separate discussion — woven mesh is interlaced and coated, laid scrim is parallel yarns chemically bonded, which makes it thinner and flatter at comparable grammage.

✔ The payoff: industry reference data puts unreinforced vinyl’s movement at up to roughly 0.4%, while glass-reinforced products typically hold at or below 0.1%.

SPC/WPC Rigid Cores: Where the Glass Layer’s Job Went

Now the question that confuses buyers most: if glass is so important in LVT, why do standard SPC layer tables not list it?

The answer is in the core. SPC is roughly 60–70% calcium carbonate, producing a dense, highly filled board that resists indentation. In an SPC plank, the rigid core has taken over much of the dimensional-stability duty.

Construction Core duty Glass layer position Typical glass grammage
Flexible LVT Polymer + filler; moves with heat Mid-plane, below decor film Follows the line and format
SPC composite with LVT layers Rigid base + stable decorative layer Between LVT base and SPC core; optional second position 10–40 g/m² (published design)
Plain SPC core Rigid, highly filled Not listed in standard layer tables —
WPC core Softer foamed core Candidate where the core alone is not stable enough Discuss with the converter

Underlayment: Paper Composite vs Foam Pad

Under the plank, a different question appears: what carries the floor, and does that layer need reinforcement?

Underlayment route Function Reinforcement Where it fits
IXPE / EVA attached pad Acoustic, comfort, minor subfloor tolerance None Standard click-floor assemblies
Paper-composite underlayment Stabilizing interlayer under flooring or carpet Fiberglass scrim + paper Thin flooring, stabilizing interlayers, separate-roll purchasing

Product Notes: Three Lines, Three Positions

GADTEX (RUIFIBER GROUP) supplies glass and polyester laid scrim into all three positions described above.

PVC-coated fiberglass laid scrim CF3*5PV for composite flooring and sports surfaces

CF3*5PV

PVC-coated fiberglass scrim for composite flooring and sports surfaces. The PVC coating ensures ideal encapsulation.

Scrim reinforced nonwoven CM3*10PH, 34 tex glass with SBR adhesive, for composite flooring and TPO

CM3*10PH

Combines 34-tex glass with SBR adhesive for nonwoven-composite constructions and TPO applications.

Fiberglass laid scrim laminated with paper for flooring and carpet underlayment

Paper-Composite

Roll goods in widths from 200 to 2500 mm for the underlayment position, providing a stabilizing interlayer.

For the selection method by production line — mesh size and grammage for LVT lines — see the earlier article in this series: fiberglass laid scrim for PVC and LVT flooring.

Frequently Asked Questions

Does SPC still need a glass layer?

A plain SPC core usually does not carry one. But when SPC is combined with LVT layers in a composite build, the mesh comes back at 10–40 g/m².

What happens if the glass layer sits too close to the surface?

It stops doing its most valuable job. Near the mid-plane it restrains bending and thermal movement most efficiently. Moved toward the surface, it contributes less stability.

Should the underlayment be paper composite or foam?

They are not competitors. Foam is for acoustic/comfort; paper-composite with glass scrim is a stabilizing interlayer.

Send us your build-up

If you produce LVT, SPC composites or paper-composite underlayment and want a scrim position checked against your stack, contact us today.

Request Recommendation & Data Sheet

WhatsApp Online Chat !